No Products in the Cart
The conventional optical trigger sensor has been replaced with a mechanical switch, resulting in a more linear and crisp trigger feel. The trigger adjustment function has been eliminated, but the trigger stroke tune allows for precise, accurate hair trigger settings. The gear sensor has been improved from sector gear detection to a cutoff cam optical detection method, making it flexible for use with DSG (dual sector gear), SSG (single sector gear), machined gears, and torque-up gears. It also provides stable operation, less susceptible to the effects of grease.
[Brushless motor compatible]
It is optimized for new generation brushless motors such as the HTG Basic Mugen brushless motor, and its compatibility has been greatly improved. The automatic active brake function allows for both crisp semi-auto firing and accurate pre-cocking.
[Bluetooth communication function (Technical Approval Certified)]
You can intuitively set it up from your smartphone or tablet using the dedicated Eshooter app (compatible with Android/iOS).
You can easily change various settings while checking the operating status in real time.
The app is distributed free of charge and is updated regularly.
[Features included in the app]
Dashboard:
You can check the number of rounds fired, firing cycle, trigger response, tip temperature, current, voltage, and operating time.
Quick Settings:
Up to three different settings can be saved, and you can instantly switch to your preferred settings by holding down the trigger for three seconds in the SAFE position.
Firing Mode Selection:
You can freely select the mode from SAFE, SEMI, BINARY, BURST, AUTO, and SNIPER.
Gear Optimization:
Compatible with single sector, DSG and machined gears, and operates optimally with a gear sensor.
Pre-cocking adjustment:
High-precision adjustment in 200 steps from 0 to 200 m/s allows fine-tuning of trigger response in all modes.
Firing Cycle Control (ROF CONTROL):
While maintaining response performance even in full auto mode, the firing cycle can be adjusted in 10% increments (40% to 100%).
Battery protection function:
It has remaining charge display, low charge warning, over-discharge prevention, and sleep mode ON/OFF settings. The sleep mode automatically switches to sleep mode after one hour of inactivity, and when reconnected, it resumes operation by simply reinserting the battery.
Active Brake/Smart Fuse:
Adaptive Active Brake prevents gear instability and stops the piston forward for longer life. Smart fuse and auto fuse protect the MOSFET from overheating, overload and short circuit.
Locked Rotor Protection:
It activates when the gears and motors are operating abnormally, stopping operation and preventing damage to the gearbox.
Sniper Delay Mode:
You can choose the firing interval from 0.5 seconds, 1 second, 2 seconds, or 3 seconds, allowing for precision shooting.
Sensor setting mode:
The status of each sensor can be checked and set at a glance, maintaining optimal calibration.
Firmware Update:
Notifications will be sent via the app and firmware updates will be supported.
The initial password is "888888":
An all reset can be performed by holding the trigger in the SAFE position for 8 seconds.
[Compatible models]
Developed based on the standard Ver. 2 gearbox (rear wiring), it is compatible with Ver. 2 gearboxes from Tokyo Marui and other manufacturers both in Japan and overseas (modifications may be required). Simply installing the Kestrel V2 SE will dramatically improve the performance of your AEG, giving you a clear advantage in shooting competitions and airsoft games.
[Main specifications]
Voltage range: 3.75-17V Compatible with LiPo, LiHv, and LiFe batteries
NiCd and nickel-metal hydride batteries cannot be used.
Standby power: 17mA
Dimensions (length x width x height): 47.4 x 28.7 x 13.5 mm
Weight: 27.6g
Product contents
Eshooter Kestrel V2SE
Shim washer
Lock washer
bis
Heat shrink tubing
T plug connector (female)
Spare sticker
Instruction manual (English)
Note
Please download the Japanese instruction manual from the official website.
*Installation requires disassembly of the electric gun.
*The warranty does not cover damage caused by incorrect installation, water damage, reverse connection, short circuit, or modifications made by the customer.
*Please note that due to the design of the electronic board, it is assumed that a Li-Po battery will be used, and therefore nickel-metal hydride batteries are not supported.
*Please remove the battery when not in use. Leaving it connected will continue to energize the electronic board, which may result in malfunction.
