[PERUN] PERUN for G28 / HK417 (VFC only)

PERUN for G28 / HK417 (VFC only)

This VFC "switch unit interchangeable" electronic trigger for the G28/HK417 series electric guns combines magnetic trigger detection with optical detection (selector/sector gear) for reliable and sharp trigger response.

This is an upgrade kit that replaces the original switch unit with the "PERUN Electronic Trigger" + "Clicker".

The built-in adjustable clicker allows you to adjust the pre-travel (front play), over-travel (rear play), and break force (force required to fire) to your liking.

[Features]

[Major features]

• Clicker

  The built-in clicker reproduces the click feeling of a real gun trigger. It requires a certain amount of force to "break" the trigger before it can fire. The amount of force required to break the trigger can be adjusted to your liking (even down to zero). Pre-travel and over-travel are also adjustable.

• Trigger sensitivity (8 levels)

  Eight sensitivity settings are available, from a short pull to a deep pull. No modifications to the trigger or gearbox are required, and adjustments can be made in the field.

• Pre-cocking (8 stages)

  Effective in situations such as CQB where a split second can make the difference between victory and defeat. When pre-cocking is enabled, the piston is held in the retracted position after each shot, and the spring is kept compressed, allowing the next bullet to be fired immediately.

  If you want to release the spring after using pre-cocking, fire one shot in semi-auto mode and then hold the trigger. The second shot will be fired and the piston will stop at its full forward position.

  Pre-cocking must be used in conjunction with active braking.

• Active brake (5 levels)

  The motor is controlled and stopped after each shot to prevent unintentional two-point bursts caused by overspin.

[Fire Mode]

You can select the firing mode that is assigned to a short or long trigger pull.

• Two-Stage Trigger

  This mode is similar to the Steyr AUG, where the firing mode changes between a short pull and a full pull.

  ・Semi-auto/Burst ・Semi-auto/Full-auto ・Burst/Full-auto

• Binary Trigger

  When set to semi-automatic, the gun will fire not only when you pull the trigger but also when you release it .

• DMR mode

  After semi-automatic firing, trigger input will not be accepted for the set number of seconds.

  You can choose from 0.25 seconds, 0.5 seconds, 1 second, 2 seconds, or 3 seconds.

• DSG mode

  This is a sector gear detection mode optimized for dual sector gear (DSG).

• ROF Control

  You can adjust the firing rate during full auto/burst firing to save bullets and create a more realistic cycle.
  *If enabled when installing certain brushless motors, there is a risk of malfunction.

[ Programming (setting method) ]

All settings can be made simply by operating the selector and trigger , and the status can be confirmed by the LED. Changes can be made in a few seconds, and settings can be switched at any time depending on the situation.

Settings are saved independently for each selector position, so you can configure it however you like, for example, "SEMI position = semi" and "AUTO position = binary."

Compatible voltage: 7V to 17V (full charge voltage)

It can be used with a wide range of batteries and is suitable for even the most demanding setups.

[Safety function]

• Li-po battery over-discharge protection

  If the voltage drops to a dangerous level, a short buzzer (or sound) will sound, repeating every minute. This feature can be turned on or off.

• Self-diagnosis system

  The AEG and MOSFET are constantly monitored, and if there is an abnormality, the LED display will immediately notify you of the cause, making troubleshooting easier.

• Electronic fuse

  If a serious malfunction (short circuit, motor lock, etc.) is detected, the battery will be automatically shut off to protect the electric gun and battery.

[Notes]

• This product is for use with airsoft guns only . Do not use with any equipment other than that specified by the manufacturer.
• Installation should be performed by someone with sufficient technical knowledge. Improper installation may result in damage to the equipment.
• Use the power supply within the product specifications. Using it beyond the allowable range may cause damage.
• Since it contains electronic components, it may be damaged by exposure to water, broken wires, incorrect battery polarity, or strong impact.
• Keep out of reach of small children.
• This product complies with CE Directive requirements. Modifications may impair safety compliance.
• If any damage is found, discontinue use immediately.
• Store at room temperature in a dry environment.