Custom Parts (2907)

The diameter of the shaft that goes into the gearbox is Φ9.4mm to Φ9.95mm in 0.05mm increments. There are a total of 12 different custom motor towers in the lineup....

RETRO ARMS CNC Gears PandoRA - Compatible with SR25 19 tooth RATIO 20:1 Special sector gear with adjustable tappet pins. A long piston with 19 teeth is required. It has...

RETRO ARMS CNC Gears PandoRA - Supports RATIO 20:1 Special sector gear with adjustable tappet pins. It has a structure that allows you to place the screw-in tappet pin at...

RETRO ARMS CNC Gears PandoRA - Supports RATIO 16:1 Special sector gear with adjustable tappet pins. It has a structure that allows you to place the screw-in tappet pin at...

RETRO ARMS CNC Gears PandoRA - RATIO 13:1 Short stroke or RETRO ARMS CNC Gears PandoRA - Special sector gear with variable tappet pins compatible with RATIO 13:1. It has...

RETRO ARMS CNC Gears PandoRA - RATIO 13:1 Short stroke or RETRO ARMS CNC Gears PandoRA - Special sector gear with variable tappet pins compatible with RATIO 13:1. This product...

RETRO ARMS CNC Gears PandoRA - RATIO 13:1 Short stroke or RETRO ARMS CNC Gears PandoRA - Special sector gear with variable tappet pins compatible with RATIO 13:1. This product...

RETRO ARMS CNC Gears PandoRA - RATIO 13:1 Short stroke or RETRO ARMS CNC Gears PandoRA - Special sector gear with variable tappet pins compatible with RATIO 13:1. This product...

RETRO ARMS CNC Gears PandoRA - Compatible with RATIO 10:1 (3mm) Special sector gear with adjustable tappet pins. This product has three pre-cut piston openings. It is a short stroke...

RETRO ARMS CNC Gears PandoRA - Compatible with RATIO 10:1 (3mm) Special sector gear with adjustable tappet pins. It has a structure that allows you to place the screw-in tappet...

This is a gear set for the RETRO ARMS V2 long gearbox (19 teeth). The gear ratio is 20:1 (20.8:1). A long piston with 19 teeth is required. No sintered...

This is a gear set for V2/V3 made by RETRO ARMS. The gear ratio is 20:1 (20.8:1). No sintered parts are used, all steel is machined and heat treated (around...

This is a gear set for V2/V3 made by RETRO ARMS. The gear ratio is 16:1 (17.28:1). No sintered parts are used, and all parts are made from machined steel...

This is a gear set for V2/V3 made by RETRO ARMS. The gear ratio is 13:1 (13.65:1). No sintered parts are used, and all parts are made from machined steel...

This is a gear set for V2/V3 made by RETRO ARMS. The shaft diameter is Φ3mm and the gear ratio is 13:1 (13.65:1). This product has four pre-cut piston openings....

This is a gear set for V2/V3 made by RETRO ARMS. The shaft diameter is Φ3mm and the gear ratio is 10:1 (10.36:1). No sintered parts are used, all steel...

●Material: Natural wood (birch) Finish: Buffing, linseed oil (checkered part) Compatible with: Marushin Colt Anaconda series ●Can be installed without processing -Fixed with genuine screws ●Made in Japan

●Material: Natural wood (birch) Finish: Unpainted, oil finish Compatible with: Marushin SIG P210-6 ●Can be installed without processing -Fixed with the screws and nuts of the original grip (see image...

RETRO ARMS V2/V3 gear set allows you to cock three times in one go. This is a triple sector gear (TSG) set. The sector gear has 5 teeth x 3,...

●Material: Natural wood (birch) Finish: Buffing, linseed oil (checkered part) Compatible with: Marushin Colt Anaconda series ●Can be installed without processing -Fixed with genuine screws ●Made in Japan

●Material: Birch ●Color: Brown Finish: Unpainted finish Genuine grip weights can be attached (see image) Grip weights are not included. Installation: Install using the original grip fixing screws - Compatible...

●Material: Birch ●Color: Brown Finish: Unpainted, buffed Compatible with: Maruzen Walther PPK/S, PP Installation: Fixed with genuine screws *No O-ring is used ●Can be installed without processing ●Made in Japan

●Material: Beech ●Finish: Oil stain paint ●Contents: Fore-end, Raptor Grip Compatible with: Maruzen CA870 ●Designed to be installed without any modification ●Made in Japan *Sold as a set of two...

●Material: Beech Finish: Oil stain paint ●Contents: Fore-end Compatible with: Maruzen CA870 ●Designed to be installed without any modification ●Made in Japan *The main unit is not included.